Home           Products           Company           Contact us     
> Statics
> Strength of Materials
> Dynamics
> Fundamentals of Engineering Design
> Machinery Diagnosis
> Properties of Materials
Products  |  Engineering Mechanics and Machine Elements  |  Strength of Materials  |  WP 130
WP 130 Verification of Stress Hypotheses Show data sheet (pdf file) Print page
Technical Description

Stress hypotheses are applied in the science of the strength of materials when calculating comparative stresses where unequal stresses are combined.

  The following stress hypotheses, taking into account material properties, have been tried and proven in practice: Rankine yield criterion (direct stress hypothesis), von Mises yield criterion (change of shape hypothesis) and Tresca yield criterion (shear stress hypothesis).

  The experimental unit WP 130 is used to verify these comparative stress hypotheses on test specimens made of various metals. For the purpose, a multi-axial stress state is produced at a point on the specimen and the resulting deformation is measured.

  The specimen is clamped on one end to the fixed frame. A loading plate is clamped to the specimen on the other end. A weight is attached on the outer circumference of the plate. A balance weight compensates for the dead-weight of the plate and the loading weight. As a result only direct and shearing stress occur at a point on the test specimen and shear forces are avoided.

  The loading plate has a graduation grid enabling weights to be attached at 15į increments. This permits purely bending moment and tor as well as combined load moments to be achieved. Diametrically opposite the weight load, measurement points are provided on the loading plate to measure the deformation. This enables the deformation at the point of maximum deflection to be measured.

  The various elements of the experiment are clearly laid-out and housed securely in a storage system.

  The well-structured instructional material sets out the fundamentals and provides a step-by-step guide through the experiments.

Learning Objectives / Experiments

- Generation of multi-axial loads on test samples
  made of ductile metals: 
  * steel, copper, brass, aluminium
- Generation of various load moments
  * purely bending moment
  * pure torque
  * combined bending moment and torque
- Determination of the yield point
- Verification of the Rankine yield criterion
- Verification of the Tresca yield criterion
- Representation in Mohrís Circle of stresses and


* Verification of the Rankine yield criterion and the
  Tresca yield criterion1
* Multi-axial loading of test specimens by pure
  bending, pure torsion or a combination of the two1
* Statically determinate system by attachment of 
  balance weights1
* Experiments with test specimens made of ductile
Available accessories
WP 130.01 -- Set of 4 Specimens Alum., Copper, Steel Brass, 1 each
WP 130.21 -- Set of 4 Specimens Aluminum
WP 130.22 -- Set of 4 Specimens Copper
WP 130.23 -- Set of 4 Specimens Steel
WP 130.24 -- Set of 4 Specimens Brass
[1] Experiments verifying comparative stress hypotheses from the science of the strength of materials
[2] 7 different load combinations of bending and torsion
[3] Loading of the test specimen without shear force by compensation for the influence of dead-weight
[4] Test specimens made of steel, copper, brass, aluminium
[5] Generation of load moments by means of weight and lever arm
[6] Measurement of the deformation at the point of maximum deflection
[7] Storage system to house the components
Technical Data

- length: 49mm
- clamping length: 11.5mm
- specimen diameter in measurement

  cross-section: d=4mm
Set of weights to place load on specimens
- 1x 2N (hanger), 1x 1N, 1x 2N, 1x 4N, 2x 8N
Set of weights to compensate for the load and the loading plate
- 1x1N, 2x2N, 1x4N, 2x8N
Lever arm: 100mm
- measuring range: 0...10mm
- graduations: 0.01mm

Dimensions and Weight
l x w x h: 390 x 330 x 360 mm
Weight: approx. 17 kg
Scope of Delivery
1 experimental unit
16 round test specimens
(4x St, 4x Cu, 4x Al, 4x brass)
1 set of weights (loading)
1 set of weights (compensation)
1 hexagon socket wrench
1 storage system
1 set of instructional material
Order Details

020.13000  WP 130  Verification of Stress

© 2005 G.U.N.T. Gerätebau GmbH