Home           Products           Company           Contact us     
> Fundamentals of Control Engineering
> Components and Calibration
> Simple Process Engineering Control Systems
> Complex Process Engineering Control Systems
> Fundamentals of Process Engineering
> Mechanical Process Engineering
> Thermal Process Engineering
> Chemical Process Engineering
> Biological Process Engineering
> Water Treatment
Products  |  Process Engineering  |  Thermal Process Engineering  |  CE 715
CE 715 Rising Film Evaporation Show data sheet (pdf file) Print page
Technical Description

  Evaporators are used in process engineering and food technology for increasing the concentration of solutions. Part of the solvent is removed by evaporation, which means that the solution retains a higher concentration of dissolved solids. Film evaporators are used in particular for temperature-sensitive solutions such as milk.
  The CE 715 allows the operating behaviour of a rising film evaporator to be investigated. The untreated solution is fed from the feed tank below into the evaporator. The evaporator is a double pipe heat exchanger that is heated by steam. The steam pressure on the casing side is adjusted with a PID controller. A cyclone is installed after the evaporator to separate the evaporated solvent and the concentrated solution. The solvent vapour removed is condensed in a water-cooled condenser and collected in a tank. The concentrated solution can also be collected in a tank or fed back into the evaporator for the concentration to be increased further.
  The two tanks, the cyclone and the condenser are made of glass for better observation. The system can also be operated under a vacuum to reduce the boiling point of the solvent. All relevant pressures, temperatures and flow rates are measured to allow evaluation and monitoring of the process.
  To clean the system while installed, a pump and cleaning nozzles are fitted in the condensate and concentrate tanks.
  Common salt and water are the recommended materials for experiments.

  The well-structured instructional material sets out the fundamentals and provides a step-by-step guide through the experiments.


Learning Objectives / Experiments

- fundamental principle of film evaporation for

  increasing the concentration of

  temperature-sensitive solutions
- investigation of the variables influencing the solid

  concentration in the solution
- influence of pressure and feed flow rate on the

  separating process
- influence of flow rate and pressure of the heating

  steam on the separating process
- investigation of the variables influencing the energy

  efficiency of the process
- energy balances at heat exchangers
- system cleaning while installed


* Rising film evaporator for increasing the

  concentration of temperature-sensitive solutions1
* Hygienic operation due to carefully selected

  materials such as stainless steel and glass1
* Cleaning possible while installed1
* Comprehensive and well-structured instructional


Available accessories
CE 715.01 -- Electrical Steam Generator 10kW

[1] rising film evaporator for increasing the concentration of temperature-sensitive solutions
[2] stainless steel steam-heated single pipe evaporator
[3] control valve for adjustment of steam pressure via PID controller
[4] vacuum pump and vacuum controller to reduce the evaporation temperature
[5] separation of concentrated solution and evaporated solvent using glass cyclone
[6] glass condenser for condensation of removed solvent vapour
[7] stainless steel feed tank
[8] glass tanks for concentrate and condensate

[9] measurement of flow rate, pressure and temperature
[10] steam supply from laboratory network or CE 715.01

Technical Data

Rising film evaporator
- heat transfer surface: approx. 0,08m

- length: approx. 1,2m

Control valve: Kvs value: 0,4m/h
Vacuum pump
- final vacuum: approx. 100mbar
- flow rate: approx. 90L/min
Vacuum controller: -100...0kPa
Condenser for solvent vapour
- heat transfer surface: approx. 0,2m
- feed: approx. 30L
- concentrate, condensate: approx. 10L each

Measuring ranges
- temperature: 7x 0...170C
- pressure: -1...1bar; 0...6bar (abs); 0...10bar
- flow rate: 2...36L/h; 0...1.000L/h


Dimensions and Weight
LxWxH: approx. 1.360x750x2.640mm
Weight: approx. 300kg
Required for Operation
230V, 50/60Hz, 1 phase or 120V, 60Hz, 1 phase
Cooling water: 200...300L/h
Compressed air (control valve): 3...4bar, max. 300L/h
Heating steam: max. 2bar, 4...6kg/h
Scope of Delivery

1 trainer

1 set of hoses

1 set of instructional material

Order Details
083.71500  CE 715  Rising Film Evaporation
© 2005 G.U.N.T. Gerätebau GmbH