Home           Products           Company           Contact us     
> Fundamentals of Control Engineering
> Components and Calibration
> Simple Process Engineering Control Systems
> Complex Process Engineering Control Systems
> Fundamentals of Process Engineering
> Mechanical Process Engineering
> Thermal Process Engineering
> Chemical Process Engineering
> Biological Process Engineering
> Water Treatment
Products  |  Process Engineering  |  Water Treatment  |  CE 579
CE 579 Depth Filtration Show data sheet (pdf file) Print page
CE 579 - A product from the GUNT 2E range
Technical Description

  Depth filtration with sand filters is a key unit operation in water treatment. CE 579 enables this process to be demonstrated.
   Raw water contaminated with solids is pumped from above into a sand filter. The solids are captured and retained as the raw water flows through the filter bed. The water itself passes through the filter bed and emerges at the bottom end of the sand filter. The treated water (filtrate) flows into a tank. Over time, more and more solids are deposited in the filter bed which increases its flow resistance. This process is detectable by the increasing pressure loss between the sand filter inlet and outlet. The flow through the sand filter decreases. Backwashing with treated water cleans the filter bed and reduces the pressure loss again.
  The sand filter is equipped with a differential pressure gauge. There are also several pressure measuring points along the filter bed. The pressures are transmitted to the manometer panel via hoses and displayed there as water column. This can be used to plot Micheau diagrams. The flow rate, temperature, differential pressure and system pressure are measured. The flow velocity in the filter bed (filter velocity) can be adjusted. Samples can be taken at all relevant points.
  A software program is provided to control the operating states and measure data. A process schematic shows the current operating states of the individual components and the measured data.

  The well-structured instructional material sets out the fundamentals and provides a step-by-step guide through the experiments.

Learning Objectives / Experiments

- learning the fundamental principle of depth filtration

  by sand filters
- observation of the pressure conditions in a filter bed
- determination of pressure losses
- plotting of Micheau diagrams
- principle of backwash

* Removal of solids by depth filtration (sand filter) 1
* Pressure loss: plotting of Micheau diagrams 1
* Backwash of sand filters

[1] depth filtration with sand filter
[2] sand filter backwash possible
[3] manometer panel with 20 tubes to measure the pressures in the filter bed
[4] plotting of Micheau diagrams
[5] raw water and backwash pump
[6] magneto-inductive flow rate sensor

[7] 4 ball valves with electric drive
[8] measurement of flow rate, differential pressure, system pressure and temperature
[9] filter velocity adjustable
[10] LabVIEW software with control functions and data acquisition via USB under Windows XP or Windows Vista


Technical Data

Sand filter
- outer diameter: 200mm
- inside diameter: 150mm
- height: 1.660mm
Raw water pump
- max. flow rate: 420L/min
- max. head: 20m
Backwash pump
- max. flow rate: 50L/min
- max. head: 37m
Tanks for raw water and treated water
- capacity: each 180L

Measuring ranges
- flow rate: 0...1.300L/h
- manometer panel: 0...1.500mmWC

- differential pressure: -1...1bar
- system pressure: 0...3bar
- temperature: 0...50C
- filter velocity: 0...70m/h

Dimensions and Weight

LxWxH: 1.300x850x2.180mm (trainer)
LxWxH: 750x640x1.900mm (manometer panel)
Total weight: approx. 250kg

Required for Operation

230V, 50Hz, 1 phase or

230V, 60Hz, 1 phase or

230V, 60Hz, 3 phases

Scope of Delivery

1 trainer
1 manometer panel

1 set of hoses
1 LabVIEW software CD + USB cable
1 set of instructional material

Order Details
083.57900  CE 579  Depth Filtration
© 2005 G.U.N.T. Gerätebau GmbH