Home           Products           Company           Contact us     
> Fundamentals of Control Engineering
> Components and Calibration
> Simple Process Engineering Control Systems
> Complex Process Engineering Control Systems
> Fundamentals of Process Engineering
> Mechanical Process Engineering
> Thermal Process Engineering
> Chemical Process Engineering
> Biological Process Engineering
> Water Treatment
Products  |  Process Engineering  |  Fundamentals of Control Engineering  |  RT 030
RT 030 Training System: Pressure Control, HSI Show data sheet (pdf file) Print page
Technical Description

  This compact experimental unit offers every opportunity to learn the fundamentals of control engineering through experimentation on a  pressure control system.

 

  The experimental set-up is mounted on a housing which accommodates all the electronics. The pressure tank is charged with compressed air by a diaphragm gas pump. The advantage of the dial-gauge manometer is that the pressure in the tank can be observed directly at any time. The pressure is measured using a pressure sensor. The sensor output signal is sent to the software controller. The output signal from the controller influences the speed of the diaphragm gas pump and hence the flow rate. An air consumer is simulated by way of a flow control valve. A solenoid valve through which air can escape can be activated by the software to investigate the influence of disturbance variables.

  The powerful state-of-the-art software is an integral part of the training system, embodying the principle of hardware/software integration (HSI). It enables the experiments to be conducted and evaluated in a user-friendly manner. The software has network capability. The link between the experimental unit and the PC is made via a USB port.

  The well-structured instructional material sets out the fundamentals and provides a step-by-step guide through the experiments.

 

Learning Objectives / Experiments

- fundamentals of control engineering based on the

  example of a pressure control system with PT1

  behaviour
- open loop control response

- effects of different controller parameters and

  methods on the response of the closed loop

  system

- recording of step responses 
  * reference variable
  * disturbance variable
- controller optimisation
- software-based controlled system simulation
  * comparison of different controlled system

     parameters

Features

* Experimental unit with diaphragm gas pump and 

  pressure tank1
* Extensive range of experiments on fundamentals of

  control engineering1
* State-of-the-art software for all experimental units

  of the
RT 010 - RT 060 series, with extensive

  controller and recorder functions1
* Software-based simulation of the controlled system

Alternative products
RT 010 -- Training System: Level Control, HSI
RT 020 -- Training System: Flow Control, HSI
RT 040 -- Training System: Temperature Control, HSI
RT 050 -- Training System: Speed Control, HSI
RT 060 -- Training System: Position Control, HSI
RT 634 -- Pressure Control Demonstration Unit
Overview
RT 010 - RT 060 Fundamentals of Process Control
Specification

[1] experimental unit for control engineering experiments
[2] pressure control in a tank
[3] speed controlled diaphragm gas pump
[4] electronic pressure sensor
[5] solenoid valve to generate disturbance variables
[6] software-based controlled system simulation
[7] process schematic on front panel

[8] networkable LabVIEW software via USB under Windows XP or Windows Vista

 

Technical Data

Diaphragm gas pump
- max. flow rate: 3L/min
- max. positive pressure: 1bar
- max. negative pressure: 250mbar abs.
Pressure tank
- capacity: 0,4L
- operating pressure: 1bar
- max. pressure: 10bar
Pressure control range: 0...1bar
Solenoid valve: Kvs: 0,11m/h
Pressure transducer: 0...1bar
Manometer: 0...1bar
Software controller configurable as P, PI, PID and switching controller
Software

- process schematic with controller type selection

  (manual, continuous controller, two- or three-point

  controller, programmer)
- time functions
- simulation function
- disturbance variable input

 

Dimensions and Weight
LxWxH: 610x430x340mm
Weight: approx. 17kg
Required for Operation
230V, 50/60Hz, 1 phase or 120V, 60Hz/CSA, 1 phase
Scope of Delivery

1 experimental unit
1 software package, complete with USB cable
1 handbook: fundamentals of control engineering

   (RT 010 - RT 060)
1 instruction manual for RT 030

Order Details

080.03000  RT 030  Training System:

                                 Pressure Control, HSI


Print
© 2005 G.U.N.T. Gerätebau GmbH