Home           Products           Company           Contact us     
> Fundamentals of Control Engineering
> Components and Calibration
> Simple Process Engineering Control Systems
> Complex Process Engineering Control Systems
> Fundamentals of Process Engineering
> Mechanical Process Engineering
> Thermal Process Engineering
> Chemical Process Engineering
> Biological Process Engineering
> Water Treatment
Products  |  Process Engineering  |  Mechanical Process Engineering  |  CE 200
CE 200 Flow Properties of Bulk Solids Show data sheet (pdf file) Print page
Technical Description

  The flow properties of a powder or bulk solid determine how it behaves during handling. For example, material may flow irregularly out of silos, or the flow of bulk solid may come to a stop. In order to avoid these problems in practice, silos can be designed on the basis of measurements using shear testers, such as the Jenike shear tester or a ring shear tester.
  In a ring shear tester, a bulk sample is contained in a ring-shaped shear cell. A normal force is exerted on the sample by way of a lid. A hanger from which a variable weight is suspended generates this normal force. A motor moves the shear cell relative to the lid in order to apply shear to the sample. For compaction (pre-shearing) the sample is subjected to a large normal force. An electronically amplified force transducer measures the shear forces which are then recorded by data acquisition software over time. After pre-shearing, shearing to failure is executed with a reduced normal force (strength measurement) and likewise recorded by the software. From the shear force characteristics, properties such as the compressive strength and internal friction of the bulk solid can be determined. To determine the density of the bulk solid, the volume of the bulk sample is ascertained by recording the lowering of the lid using a vernier caliper gauge. So as to also take into account the influence of the hopper wall material on the outflow behaviour, a separate measurement is performed with a ring-shaped sample of the wall material.

  An evaluation software is available to determine the flow properties

from the experimental results. The flow properties identified are used to determine the optimum geometry of a silo's discharge hopper. Trainer CE 210 is provided for practical verification of the design results obtained in terms of mass flow/funnel flow. The ring shear tester and the evaluation software were developed by Prof. Dr. Schulze (from Braunschweig / Wolfenbüttel University of Applied Sciences).
 

Learning Objectives / Experiments

- recording the shear force characteristics of bulk

  solids
- yield locus and wall yield locus design
- determination of flow properties
  * compressive strength
  * internal friction
  * density
  * wall friction angle
- determination of the optimum hopper geometry

  of a bulk solids silo

Features

* Determination of the flow properties of bulk solids

  using a ring shear tester for the design of silos1
* Easy handling based on unlimited shear travel1
* Professional analysis software

Specification

[1] design of bulk solids silos using a ring shear tester
[2] 1 ring-shaped shear cell to determine yield loci

[3] 1 ring-shaped shear cell with sample of wall material to determine wall yield loci

[4] shearing of the bulk solid sample by motor rotation of the shear cell
[5] vertical loading of the sample via ring-shaped lid with weights
[6] force sensor to measure the shear forces
[7] vernier caliper gauge to measure the change in height and density of the bulk sample

[8] LabVIEW software to record the shear force characteristics via USB under Windows XP or Windows Vista
[9] evaluation software to determine the relevant bulk solid parameters

  

Technical Data

Shear cell
- sample volume: approx. 70cm3
- material: aluminium

Shear cell with sample of wall material

- sample volume: approx. 15cm3
- material: aluminium
Motor
- power consumption: max. 75W
- speed: 500...3.000min-1
1 set of weights

- 4x 500g
- 2x 200g

- 2x 100g
- 2x 50g
 

Measuring ranges
- shear force: 0...40N
- balance: 0...1.000g

  

Dimensions and Weight
LxWxH: approx. 550x300x450mm
Weight: approx. 30kg
Required for Operation

230V, 50/60Hz, 1 phase and 120V, 60Hz, 1 phase

Scope of Delivery

1 experimental unit

1 shear cell

1 shear cell with sample of wall material
1 vernier caliper gauge

1 LabVIEW software cd + USB-cable
1 evaluation software

1 packing unit of bulk solid
1 balance
1 set of instructional material

Order Details
083.20000  CE 200  Flow Properties of Bulk Solids
Print
© 2005 G.U.N.T. Gerätebau GmbH